欢迎你了解多功能弯曲机，本机器是以液压油缸推进为动力，采用更换模具来实现多元化加工为一体的机器。

Welcome to understand the multi-function bending machine, this machine is powered by hydraulic cylinder propulsion, using the replacement of the mold to achieve a variety of processing as one of the machine,

加工后的工件分别为三角形、正方形、矩形、多边形，加工范围高度在150mm以内，加工厚度在14mm以内。

The processed workpieces are triangular, square, rectangular, and polygon, with processing range height within one hundred and fifty millimetey and processing thickness within fourteen millimetey.

最小内径可控制在23mm以内。

The inner diameter can be controlled within twenty-three millimetey

冲孔模具可以加工圆形孔，方形孔，矩形孔等形状 同时还可以加工圆管豁口，更多更多说明请参考技术方案

Punch mold can be processed circular holes, square holes, rectangular holes and other shapes can also be processed circular pipe gap, for more instructions, please refer to the technical scheme

切断模具可以加工厚度14mm板宽135mm以内的型材。长度可以定点控制

Cutting molds can process profiles with a thickness of fouteen millimetey and one hundred and thirty-five millimetey . Length can be fixed-point control

型材切断模具可以切断方管，圆管和角钢

Section cutting mold can cut off the square pipe, round pipe and corner steel

弯圆管模具可以加工直径在48mm以内的管材。圆R的控制是靠推进模具控制

Round pipe molds can process pipes within forty-eight millimetey in diameter. The circular arc is controlled by advancing the mold

校平模具可以校正各内型材，他的优点是可以矫正也可以弯曲一定的弧度。

The leveling mold can correct each internal profile, and its advantage is that it can correct or bend a certain radian.

缩管模具可以加工不同的管子，不同管子而且只需要一个收缩模具。

The shrink mold can process different tubes, different tubes and it only need one shrink mold.

机器工作台采用高强度钢材回火处理不变形，液压元件采用YUKEN,电器采用Schneider电器元件，重复精度控制在0.05mm

The machine bench adopts high strength steel tempering treatment without deformation, hydraulic components use yuken, electrical appliances use schneider electrical components, repetition accuracy is controlled at zero point zero five millimetey

该机器只需要更换不同的模具就可以加工各类型材，功能强大，投资少

The machine only needs to replace different molds can process all kinds of profiles, powerful function, less investment

压力控制采用远程调压阀控制，

Pressure control using a remote pressure regulator control,

机器采用模块化组合，操作界面有中文模式和英文模式，控制方式有手动模式，半自动模式和全自动模式。

The machine adopts the modular combination, the operation interface has the Chinese mode and the English mode, the control mode has the manual mode, the semi-automatic mode and the fully automatic mode.

电源电压采用380V50HZ,如果需要特殊模具和特殊电压请联系我们经销商

Power supply voltage is three hundred and eighty volts  fifty hertz. If special mold and special voltage are required, please contact our dealer

折弯   卷板     冲孔   剪板     扩管     切方管     切角铁    弯方管      校平

Plate bending  plate rolling  piercing; punching  Cut the board pipe expanding

Cut square tube

Cut Angle iron

Bend square tube

Bend round tube

Straightening